Samsung Washer OE Error Code: Overflow & What to Check First

Written by: Appliance Sleuth Editorial Team

Published September 15, 2026 · Last reviewed September 17, 2026

✓ Verification: Manufacturer-verified against Samsung US Support (2026-09-17)

Applies to: Samsung washers (OE/0E/OC/0C are the overflow family)

⚠️ Safety first: unplug the appliance before opening it. Don't work on gas or sealed refrigerant systems, never bypass lid/door locks, and if a step needs live voltage, gas, or a sealed system it's a technician job. DIY can void your warranty.

Appliance Sleuth is reader-supported. We may earn a commission when you purchase through links on this page, at no additional cost to you.

⚠️ Safety — stop the incoming water first. OE is an overflow code: there is too much water in the washer. Before any check, close the hot and cold water-supply valves. Unplugging the washer does not shut off the water. If water keeps entering after the valves are closed, isolate the water supply (for example, at the house shutoff) and request service — do not keep running cycles.

Short answer: Samsung lists OE — and the related displays 0E / OC / 0C — as an overflow error: there is too much water in the washer. Shut off the water supply at the hot and cold valves. If water keeps entering after the valves are closed, isolate the supply and request service. Samsung’s public guidance does not attribute the overflow to a component the owner should replace.

What OE means (per Samsung)

Per Samsung US Support, OE is an overflow error: there is too much water in the washer. This is a water-management fault, so the priority is stopping water from continuing to enter the machine — not diagnosis-first. Samsung’s water-fill guidance for a washer that keeps filling is to shut off the water valves and request service.

Code family & alternate displays

This page covers the OE / 0E / OC / 0C overflow family on Samsung washers — the same fault under different display strings. Display formatting varies by model year; if your panel shows a different string, check your model’s manual before acting.

Safe first checks (what Samsung documents)

  1. Turn off the water supply. Close the hot and cold water-supply valves. This stops new water from entering the washer.
  2. Check whether water is still entering. With the valves closed, watch the drum. If water continues to enter, do not keep running cycles — isolate the water supply (for example, at the house shutoff) and request service.
  3. Remove standing water per your model’s manual before doing anything else with the machine. Follow your model’s manual for draining; do not tip or move the washer with water inside.

Never bypass the door or lid interlock, and do not run a cycle while water keeps entering the machine.

Diagnostic branches

  • Water keeps entering after the valves are closed. Samsung’s water-fill guidance is to shut off the water valves and request service. Isolate the water supply (for example, at the house shutoff) and arrange service — do not keep running cycles. Stop here.
  • You cannot stop the incoming water. Direct this to immediate help isolating the water supply. It is a water-supply condition, not a washer-component diagnosis, and should not be treated as one.
  • Water stops once the valves are closed. Remove the standing water per your model’s manual, leave the supply valves closed, and arrange service before running the machine again.

Do not replace this part yet

Don’t order a valve or any part on the code alone. Samsung presents OE as an overflow condition, and its water-fill guidance is to shut off the water valves and request service — Samsung’s public pages do not attribute OE to a failed component for owner-level replacement. Confirm any part against your exact model number and a technician’s diagnosis before buying.

When to stop and call a technician

If water keeps entering after the supply valves are closed, isolate the water supply and arrange service; do not keep running cycles. Have the model number ready. Further diagnosis may require a qualified technician. Never perform exposed live-voltage testing; parts must be serviced with the power disconnected.

Sources

Primary documentation used to verify the technical claims on this page.